Stud chucks made of brass for weld studs up to 35mm.
Standard stud chucks for use with PS-0K, PS-1, PS-1K, PS-3, PS-3K welding guns.
Diameter approx. 10mm, length approx. 50mm

Coppered stud chucks for weld studs up to 35mm.
Stud chucks for use with PS-0K, PS-1, PS-1K, PS-3, PS-3K welding guns. Diameter approx. 10mm, length approx. 50mm
Please note: Similar to a standard stud chuck, however, made of copper. Higher tool life, better conductivity

Stud chucks made of brass for weld studs up to 55mm.
Special chucks for use with PS-1, PS-1K, PS-3, PS-3K welding guns. Diameter approx. 10mm, length approx. 70mm.
Please note: Depending on the type of welding gun used, longer ground legs or longer support tubes are required.

Earth tag chucks made of brass F1 / F2 6.3mm
Special chucks for PS, PS-3, PS-3K

Standard stud chucks for use with the PH-3N welding gun. Finish: brass zinc-plated

Support tube made of brass with a galvanized surface.
Wear part for the PS-1K stud welding gun.
Diameter 30mm, Length for a projection of 25mm (standard length)

Sleeve nut SW14 (wrench size 14mm)
Wear part for PS-0K, PS-1K, PK-0K stud welding guns (standardised product)

Spare part for the PS-1K stud welding gun

Support leg made of brass (including M5 threaded pin)
Diameter approx. 8mm, length approx. 25mm (standard length)
The support legs can be replaced by the support tube (standard).
n.b. Three support legs are required for the stud welding gun.

Support leg made of brass (including M5 threaded pin)
Diameter approx. 8mm, length approx. 53mm (special length)
The support legs can be replaced by the support tube (standard).
n.b. Three support legs are required for the stud welding gun.
n.b. Depending on the type of welding gun used, longer stud chucks are required.

Ground leg (support leg) made of stainless steel.
Suitable for the PS-1 welding gun. Diameter: approx. 6mm, length: approx.50 mm (without thread), thread: M4 (standard length)
n.b. Three support legs are required for the stud welding gun.

Ground leg (support leg) made of stainless steel.
Suitable for the PS-1 welding gun. Diameter: approx. 6mm, length: approx. 80mm, thread: M4 (special length)
n.b. Three support legs are required for the stud welding gun.
n.b. Depending on the type of welding gun used, longer stud chucks are required.

Foot ring made of stainless steel.
Wear part for PS-1, PS-3 and PS-3K stud welding guns (standardised product)

Sleeve nut SW17 (wrench size 17mm)
Wear part for PS-1, PS-3, PS-3K stud welding guns (standardised product)

Please note: If necessary, shorten bellows before installing it.

Support tube made of aluminium
Wear part for the PS-1 stud welding gun. Diameter: 40mm, length: 80mm (standard length)

Support tube made of aluminium - special type
Wear part for the PS-1 stud welding gun. Tapered front end (30mm diameter). Length: 80mm (standard length)

Support tube made of aluminium - special type
Wear part for the PS-1 stud welding gun. Tapered (30mm diameter) split front end. Length: 80mm (standard length)

Support tube made of stainless steel - special type
Wear part for the PS-1 stud welding gun. Tapered (30mm diameter) front end with cross hairs. Length: 80mm (standard length)